The container office is similar to the building. It levels the surrounding area and the base of the partition wall. It is made of reinforced concrete, which is more solid. Then the pillars are connected with the skeleton with transverse beams, and the upper partitions, the outer wall panels and the doors and windows frame are connected; then the floor is laid and the upper floor is installed, then the roof truss and the roof panels are mounted; finally, the doors and windows are installed, and the vertical support is pulled. There are also sanitary ware, hardware and so on. Next, the resident container manufacturer will give us a detailed introduction to the matters needing attention in the process of construction! _________

1.各构件装置位置应契合设计请求，现场焊接部件位应精确，无假焊、漏焊。紧固件应契合GB5782规则，螺栓必需按设计请求的规则，位置装置正确并垫好垫圈，不得少装、漏装；构件间的衔接螺栓必需要拧紧。

1. The location of each component should meet the design requirements, and the location of field welding components should be precise, without false welding or leakage welding. Fasteners should conform to GB5782 rules. Bolts must be in accordance with the design requirements. Location devices should be correct and gaskets should be padded properly. No less or less filling should be allowed. Connection bolts between components must be tightened.

2.经现场焊接及运输途中底漆剥落处应重刷防锈漆一层，构件露明部位刷面漆二层，油漆不得有漏刷、脱皮、挂漆及返锈现象。

2. After welding and transportation on site, the primer spalling should be repainted with one layer of anti-rust paint, and the component exposed part should be repainted with two layers of top paint. No leakage, peeling, hanging and rust-back of the paint should be allowed.

3.按排板图将集装箱办公室、墙面块必需校正，伞墙的转角处及阳角处用角铝封口，板与板之间衔接采用工字铝衔接，各墙须垂直，嵌缝深度分歧，划一清洁，墙面应清洁，颜色分歧，板缝齐整，打钉面上下要分歧，不得有参差，必要部位采用自攻螺栓。按设计图纸标明集装箱会议室门窗位置，用切割机割出门窗洞位置，依照门窗洞位置装置窗门，窗为塑钢窗，北京集装箱活动房租赁停止底层的吊顶。

3. The first piece of container office and wall must be corrected according to the layout. The corner and sunny corner of umbrella wall should be sealed with angle aluminium. The connection between the board and the board should be made of I-shaped aluminium. The walls should be vertical, the depth of insertion should be different, and the wall should be clean, the color should be different, the board seams should be neat, the nailing surface should be divergent, there should be no difference between the top and bottom, and the necessary parts should be self-tapping bolts. According to the design drawings, the position of the door and window of the container meeting room is marked, and the position of the door and window hole is cut out by cutting machine. According to the position of the door and window hole, the window is made of plastic steel window. The suspended ceiling of the bottom floor of the Beijing container moving room is leased.

4.门窗位置装置正确并用螺栓紧固。装置开启灵敏而无阻滞现象，玻璃不应有麻面和裂痕，玻璃干净，附件装置结实。

4. The door and window positioning device is correct and bolted. The device opens sensitively without blocking. There should be no pitting and cracks in the glass. The glass is clean and the accessory device is strong.

5.外观请求：①墙须垂直平整分歧，划一清洁。②墙面应清洁，颜色分歧，板缝齐整。③门窗锁开关灵敏，不得缺附件。

5. Appearance Requirements: 1. The walls shall be vertical, flat and divided, and uniformly cleaned. (2) The walls should be clean, with different colours and neat joints. (3) The door and window lock switch is sensitive and can not be without accessories.

以上精彩内容由济南住人集装箱整理提供，更多关于住人集装箱的详情，欢迎咨询我们官网的客服人员：http://www.jnpkjzx.com！我们将会尽快给您做出回复！谢谢大家的支持！

The above wonderful contents are provided by Jinan Resident Containers. More details about Resident Containers are welcome to consult our customer service staff on our official website: http://www.jnpkjzx.com! We will reply to you as soon as possible! Thank you for your support!